Mother Broadband: Mother Broadband

Tuesday, August 12, 2008

Mother Broadband

These are highly-regulated services traditionally intended for businesses, that are managed through Public Service Commissions (PSCs) in each state, must be fully defined in PSC tariff documents, and have management rules dating back to the early 1980s which still refer to teletypes as potential connection devices. As such, T-1 services have very strict and rigid service requirements which drive up the provider's maintenance costs and may require them to have a technician on standby 24 hours a day to repair the line if it malfunctions. (In comparison, ISDN and DSL are not regulated by the PSCs at all.) Due to the expensive and regulated nature of T-1 lines, they are normally installed under the provisions of a written agreement, the contract term being typically one to three years. However, there are usually few restrictions to an end-user's use of a T-1, uptime and bandwidth data rates may be guaranteed, quality of service may be supported, and blocks of static IP addresses are commonly included.

Since a T-1 was originally conceived for voice transmission, and voice T-1's are still widely used in businesses, it can be confusing to the uninitiated subscriber. It is often best to refer to the type of T-1 being considered, using the appropriate "data" or "voice" prefix to differentiate between the two. A voice T-1 would terminate at a phone company's central office (CO) for connection to the PSTN; a data T-1 terminates at a point of presence (POP) or data center. The T-1 line which is between a customer's premises and the POP or CO is called the local loop. The owner of the local loop need not be the owner of the network at the POP where your T-1 connects to the Internet, and so a T-1 subscriber may have contracts with these two organizations separately.

The nomenclature for a T-1 varies widely, cited in some circles a DS-1, a T1.5, a T1, or a DS1. Some of these try to distinguish amongst the different aspects of the line, considering the data standard a DS-1, and the physical structure of the trunk line a T-1 or T-1.5. They are also called leased lines, but that terminology is usually for data rates under 1.5 Mbit/s. At times, a T-1 can be included in the term "leased line" or excluded from it. Whatever it is called, it is inherently related to other broadband access methods, which include T-3, SONET OC-3, and other T-carrier and Optical Carriers. Additionally, a T-1 might be aggregated with more than one T-1, producing an nxT-1, such as 4xT-1 which has exactly 4 times the bandwidth of a T-1.

When a T-1 is installed, there are a number of choices to be made: in the carrier chosen, the location of the demarcation point, the type of channel service unit (CSU) or data service unit (DSU) used, the WAN IP router used, the types of bandwidths chosen, etc. Specialized WAN routers are used with T-1 lines that route Internet or VPN data onto the T-1 line from the subscriber's packet-based (TCP/IP) network using customer premises equipment (CPE). The CPE typical consists of a CSU/DSU that converts the DS-1 data stream of the T-1 to a TCP/IP packet data stream for use in the customer's Ethernet LAN. It is noteworthy that many T-1 providers optionally maintain and/or sell the CPE as part of the service contract, which can affect the demarcation point and the ownership of the router, CSU, or DSU.

Although a T-1 has a maximum of 1.544 Mbit/s, a fractional T-1 might be offered which only uses an integer multiple of 128 kbit/s for bandwidth. In this manner, a customer might only purchase 1/12th or 1/3 of a T-1, which would be 128 kbit/s and 512 kbit/s, respectively.

T-1 and fractional T-1 data lines are symmetric, meaning that their upload and download data rates are the same.

Wired Ethernet
Where available, this method of broadband connection to the Internet would indicate that the Internet access is very fast. However, just because Ethernet is offered doesn't mean that the full 10, 100, or 1000 Mbit/s connection is able to be utilized for direct Internet access. In a college dormitory for example, the 100 Mbit/s Ethernet access might be fully available to on-campus networks, but Internet access bandwidths might be closer to 4xT-1 data rate (6 Mbit/s). If you are sharing a broadband connection with others in a building, the access bandwidth of the leased line into the building would of course govern the end-user's data rate.

However, in certain locations, true Ethernet broadband access might be available. This would most commonly be the case at a POP or a data center, and not at a typical residence or business. When Ethernet Internet access is offered, it could be fiber-optic or copper twisted pair, and the bandwidth will conform to standard Ethernet data rates of up to 10 Gbit/s. The primary advantage is that no special hardware is needed for Ethernet. Ethernet also has a very low latency.

Rural broadband
One of the great challenges of broadband is to provide service to potential customers in areas of low population density, such as to farmers, ranchers, and small towns. In cities where the population density is high, it is easy for a service provider to recover equipment costs, but each rural customer may require expensive equipment to get connected.

Several rural broadband solutions exist, though each has its own pitfalls and limitations. Some choices are better than others, but are dependent on how proactive the local phone company is about upgrading their rural technology.

Wireless Internet Service Provider (WISPs) are rapidly becoming a popular broadband option for rural area

No comments:

Post a Comment

Broadband Internet access

Broadband Internet access, often shortened to just broadband, is high-speed Internet access—typically contrasted with dial-up access over a modem.
Dial-up modems are generally only capable of a maximum bitrate of 56 kbit/s (kilobits per second) and require the full use of a telephone line—whereas broadband technologies supply at least double this speed and generally without disrupting telephone use. (Though the opposite word for broadband is not dial up, it is used here for practical understanding purposes only.)
Although various minimum speeds have been used in definitions of broadband, ranging up from 64 kbit/s up to 1.0 Mbit/s, the 2006 OECD report is typical in counting only download speeds equal to or faster than 256 kbit/s as broadband, and the US FCC currently defines broadband as anything above 768 kbit/s
Speeds are defined in terms of maximum download because several common consumer broadband technologies such as ADSL are "asymmetric"—supporting much slower maximum upload speeds than download.
"Broadband penetration" is now treated as a key economic indicator.

Overview
Broadband is often called high-speed Internet, because it usually has a high rate of data transmission. In general, any connection to the customer of 256 kbit/s (0.256 Mbit/s) or more is considered broadband Internet. The International Telecommunication Union Standardization Sector (ITU-T) recommendation I.113 has defined broadband as a transmission capacity that is faster than primary rate ISDN, at 1.5 to 2 Mbit/s. The FCC definition of broadband is 200 kbit/s (0.2 Mbit/s) in one direction, and advanced broadband is at least 200 kbit/s in both directions. The Organization for Economic Co-operation and Development (OECD) has defined broadband as 256 kbit/s in at least one direction and this bit rate is the most common baseline that is marketed as "broadband" around the world. There is no specific bitrate defined by the industry, however, and "broadband" can mean lower-bitrate transmission methods. Some Internet Service Providers (ISPs) use this to their advantage in marketing lower-bitrate connections as broadband.
In practice, the advertised bandwidth is not always reliably available to the customer; ISPs often allow a greater number of subscribers than their backbone connection can handle, under the assumption that most users will not be using their full connection capacity very frequently. This aggregation strategy works more often than not, so users can typically burst to their full bandwidth most of the time; however, peer-to-peer (P2P) file sharing systems, often requiring extended durations of high bandwidth, stress these assumptions, and can cause major problems for ISPs who have excessively overbooked their capacity. For more on this topic, see traffic shaping. As takeup for these introductory products increases, telcos are starting to offer higher bit rate services. For existing connections, this most of the time simply involves reconfiguring the existing equipment at each end of the connection.
As the bandwidth delivered to end users increases, the market expects that video on demand services streamed over the Internet will become more popular, though at the present time such services generally require specialized networks. The data rates on most broadband services still do not suffice to provide good quality video, as MPEG-2 video requires about 6 Mbit/s for good results. Adequate video for some purposes becomes possible at lower data rates, with rates of 768 kbit/s and 384 kbit/s used for some video conferencing applications, and rates as low as 100 kbit/s used for videophones using H.264/MPEG-4 AVC. The MPEG-4 format delivers high-quality video at 2 Mbit/s, at the high end of cable modem and ADSL performance.
Increased bandwidth has already made an impact on newsgroups: postings to groups such as alt.binaries.* have grown from JPEG files to entire CD and DVD images. According to NTL, the level of traffic on their network increased from a daily inbound news feed of 150 gigabytes of data per day and 1 terabyte of data out each day in 2001 to 500 gigabytes of data inbound and over 4 terabytes out each day in 2002.

Mother Broadband

Tuesday, August 12, 2008